Skip to content
Services

Shop Floor Coating

Heavier-duty floor systems for shops, outbuildings, and small commercial spaces — specified for dragged equipment, solvent splashes, and long days on your feet.

  • Locally Owned
  • Built for Eastern Oregon
  • Diamond-Ground Prep
  • Polyaspartic Topcoat
  • Written Warranty Available

A shop floor is not a garage floor

The loads are different and so is the failure mode. A garage floor mostly fights hot tires and road salt. A shop floor fights dragged steel, dropped tools, jack stands concentrating a load onto four small points, welding spatter, and chemicals that sit on the surface rather than getting wiped up. That calls for a reinforced base coat and a thicker build than a residential garage needs.

Contamination is the thing to find early

Any shop slab that has been in use for a decade has absorbed something. Oil that has soaked in over twenty years will keep migrating up through a new coating if prep does not deal with it, and that is the single most common reason a shop floor recoat fails. On a contaminated slab we grind deeper and test the surface before committing to a system. On the old mill and shop buildings around Elgin this is routine rather than exceptional.

Slip texture where it matters

A shop floor that gets washed down is a shop floor somebody walks on wet. We can broadcast an aggregate into the topcoat to raise the slip resistance in the areas that need it — around a washdown, a door, or a bay — without making the whole floor harder to sweep. It is a per-zone decision, not an all-or-nothing one, and worth talking through on site.

Large slabs and control joints

Farm shops and outbuildings mean bigger pours, and bigger pours mean more control joints. Those joints exist because the slab is going to move, and coating across one flat guarantees a crack along the line it was always going to crack on. We plan the layout around the joints and the door so the crew is never working itself into a corner, and so the floor ends where it should.

System

Built into
every floor.

No upgrade tiers, no premium add-ons. The same specification goes down on a single-stall garage and a 4,000 sq ft shop.

01

Diamond-Ground Concrete Prep

Mechanical prep — not just etching. The slab is opened up so the coating bonds to clean, profiled concrete.

02

Full Chip Broadcast

Vinyl color flakes broadcast into a wet base coat for a fully covered, dimensional finish.

03

UV-Stable Polyaspartic Topcoat

A polyaspartic topcoat is laid over the flake — designed to resist yellowing, scratching, and tire pickup.

04

Stain & Chemical Resistant

Designed to help resist oil, automotive fluids, and common garage and shop chemicals.

05

Designed for Freeze-Thaw

Specified for the realities of Eastern Oregon weather — long winters, sudden warm-ups, full-sun summers.

06

Locally Owned, Owner-Led

Locally based in La Grande. Installation is owner-led, and every quote includes the warranty terms in writing.

Process

Five steps,
one slab at a time.

Each step is done in sequence on a single floor. We don't run multiple jobs in parallel — when your floor is in, we're on it.

  1. 01

    Grind

    The slab gets diamond-ground with HEPA-vacuumed grinders. This opens the concrete profile so the coating can lock into clean, sound substrate.

  2. 02

    Repair

    Cracks, pits, and spalls are routed out and filled with structural repair material. The whole floor is brought to a uniform plane before any coating goes down.

  3. 03

    Base Coat

    A pigmented epoxy or polyaspartic base is rolled across the prepped slab — the bonding layer and color foundation for the finish.

  4. 04

    Chip Broadcast

    While the base is wet, vinyl color flakes are broadcast to full rejection. Excess is collected the next day and the surface is scraped flush.

  5. 05

    Polyaspartic Topcoat

    A UV-stable polyaspartic topcoat seals the floor — fast-curing, scratch- and chemical-resistant, and ready for use the next day.

FAQ

Shop Floor Coating — questions

Can you coat a floor in the winter?

Usually, yes. Polyaspartic cures at temperatures that stop an epoxy outright, which is a large part of why we run it in Eastern Oregon. An unheated garage in La Grande or an outbuilding in Cove is workable through most of the winter. What we cannot work around is a wet or frozen slab, so the honest answer for any given week is that we look at the forecast and the floor together.

Why does epoxy peel, and will this do the same thing?

Almost every peeling floor traces back to preparation, not product. A coating rolled over a sealed or acid-etched slab has nothing mechanical to grip and releases in sheets the first time a hot tire sits on it. We diamond-grind every slab instead of etching, which cuts a profile into the concrete and takes off old sealers and contamination in the same pass. That bond is the part that determines whether a floor lasts.

My slab has cracks. Is it still a candidate?

Usually. Cracks get chased out and filled as part of prep rather than coated over — a crack that still moves under a coating will telegraph through the finish within a season. Control joints are a different thing and get respected rather than filled flat. What we do want to look at in person is whether a crack is stable or still moving, because that changes the answer.

How long does a floor take?

A standard two-car garage is typically a single day, start to finish, with the floor walkable that evening. Larger shop floors and farm buildings run longer, and outdoor work depends on the weather window. Wallowa County jobs are scheduled as full days rather than split visits, because the drive over the hill makes coming back mid-cure impractical.

How do I clean it?

Sweep or dust mop for the day-to-day, and a damp mop with a neutral cleaner when it needs more. Skip anything citrus-based or strongly acidic. A full-flake finish hides the ordinary scuffing that shows up immediately on a solid color, which is part of why we broadcast to refusal rather than speckling it.

Service area

Where we install

Based in La Grande, working across 4 counties. If you are outside this list, call and ask — the answer is often yes.

  • La Grande Our home town Union
  • Island City About 5 minutes from La Grande Union
  • Cove About 20 minutes from La Grande Union
  • Union About 20 minutes from La Grande Union
  • Imbler About 20 minutes from La Grande Union
  • Elgin About 25 minutes from La Grande Union
  • North Powder About 25 minutes from La Grande Union
  • Baker City About 45 minutes from La Grande Baker
  • Wallowa About 50 minutes from La Grande Wallowa
  • Pendleton About 55 minutes from La Grande Umatilla
  • Enterprise About 1 hr 5 min from La Grande Wallowa
  • Joseph About 1 hr 10 min from La Grande Wallowa
Forested mountains in Eastern Oregon
Get a quote

Free on-site quote
in Eastern Oregon.

Send a few details about your slab. We'll come measure, walk the floor, and write the quote — including the warranty terms — on the same visit.

Start a Quote
Contact

Tell us about
the slab.

Have photos you'd like to share?

Optional — up to 5 photos of the floor, 10 MB each.

By submitting, you agree to our Privacy Policy and Terms.